du.sePublications
Change search
Link to record
Permanent link

Direct link
BETA
Gyhlesten Back, Jessica
Publications (5 of 5) Show all publications
Lindgren, L.-E. -. & Gyhlesten Back, J. (2019). Elastic properties of ferrite and austenite in low alloy steels versus temperature and alloying. Materialia, 5, Article ID 100193.
Open this publication in new window or tab >>Elastic properties of ferrite and austenite in low alloy steels versus temperature and alloying
2019 (English)In: Materialia, ISSN 2589-1529, Vol. 5, article id 100193Article in journal (Refereed) Published
Place, publisher, year, edition, pages
Elsevier, 2019
National Category
Materials Engineering
Research subject
Steel Forming and Surface Engineering
Identifiers
urn:nbn:se:du-29525 (URN)10.1016/j.mtla.2018.100193 (DOI)2-s2.0-85061033793 (Scopus ID)
Available from: 2019-02-19 Created: 2019-02-19 Last updated: 2019-02-19Bibliographically approved
Gyhlesten Back, J. & Lindgren, L.-E. (2018). Modelling of the influence of prior deformation of austenite on the martensite formation in a low-alloyed carbon steel. Paper presented at THERMEC 2018. Materials Science Forum, 941, 95-99
Open this publication in new window or tab >>Modelling of the influence of prior deformation of austenite on the martensite formation in a low-alloyed carbon steel
2018 (English)In: Materials Science Forum, ISSN 0255-5476, E-ISSN 1662-9752, Vol. 941, p. 95-99Article in journal (Refereed) Published
Abstract [en]

The current work aims at developing models supporting design of the rolling and quenching processes. This requires a martensite formation model that can account for effect of previous plastic deformation as well as evolution of stress and temperature during the quenching step. The effect of deformation prior to the cooling on the transformation is evaluated. The experimental result shows that prior deformation impedes the martensite transformation due to the mechanical stabilisation of the austenite phase. Larger deformation above 30% reduces the effect of the mechanical stabilisation due to increase in martensite nucleation sites. The computed transformation curves, based on an extended version of the Koistinen-Marburger equation, agree well with experimental results for pre-straining less than 30 %. 

Keywords
Dilatometry, Koistinen-Marburger, martensite, phase transformation, modelling
National Category
Materials Engineering
Research subject
Steel Forming and Surface Engineering
Identifiers
urn:nbn:se:du-29259 (URN)10.4028/www.scientific.net/MSF.941.95 (DOI)000468152500016 ()2-s2.0-85064075553 (Scopus ID)
Conference
THERMEC 2018
Available from: 2019-01-07 Created: 2019-01-07 Last updated: 2019-06-10Bibliographically approved
Gyhlesten Back, J. & Engberg, G. (2017). Investigation of parent austenite grains from martensite structure using EBSD in a wear resistant steel. Materials, 10(5), Article ID 453.
Open this publication in new window or tab >>Investigation of parent austenite grains from martensite structure using EBSD in a wear resistant steel
2017 (English)In: Materials, ISSN 1996-1944, E-ISSN 1996-1944, Vol. 10, no 5, article id 453Article in journal (Refereed) Published
Abstract [en]

Crystallographic reconstruction of parent austenite grain boundaries from the martensitic microstructure in a wear resistant steel was carried out using electron backscattered diffraction (EBSD). The present study mainly aims to investigate the parent austenite grains from the martensitic structure in an as-rolled (reference) steel sample and samples obtained by quenching at different cooling rates with corresponding dilatometry. Subsequently, this study is to correlate the nearest cooling rate by the dilatometer which yields a similar orientation relationship and substructure as the reference sample. The Kurdjumov-Sachs orientation relationship was used to reconstruct the parent austenite grain boundaries from the martensite boundaries in both reference and dilatometric samples using EBSD crystallographic data. The parent austenite grain boundaries were successfully evaluated from the EBSD data and the corresponding grain sizes were measured. The parent austenite grain boundaries of the reference sample match the sample quenched at 100 °C/s (CR100). Also the martensite substructures and crystallographic textures are similar in these two samples. The results from hardness measurements show that the reference sample exhibits higher hardness than the CR100 sample due to the presence of carbides in the reference sample.

Place, publisher, year, edition, pages
MDPI, 2017
Keywords
Dilatometry, Hardness, EBSD, Martensite, Austenite, Kurdjumov-Sachs
National Category
Other Materials Engineering
Research subject
Steel Forming and Surface Engineering
Identifiers
urn:nbn:se:du-24715 (URN)10.3390/ma10050453 (DOI)000404411000005 ()28772813 (PubMedID)
Note

Open Access APC beslut 10/2017

Available from: 2017-03-09 Created: 2017-04-18 Last updated: 2017-11-29Bibliographically approved
Gyhlesten Back, J. (2017). Modelling and Characterisation of the Martensite Formation in Low Alloyed Carbon Steels. (Licentiate dissertation). Luleå: Luleå University of Technology
Open this publication in new window or tab >>Modelling and Characterisation of the Martensite Formation in Low Alloyed Carbon Steels
2017 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

The current work contains experimental and theoretical work about the formation of martensite from the austenitic state of the steel Hardox 450. Simulation of rolling and subsequent quenching of martensitic steel plates requires a model that can account for previous deformation, current stresses and the temperature history, therefore dilatometry experiments were performed, with and without deformation. Two austenitization schedules were used and in the standard dilatometry the cooling rates varied between 5-100 °C/s, in order to find the minimum cooling rate that gives a fully martensitic microstructure. Cooling rates larger than 40°C/s gave a fully martensitic microstructure. The cooling rate of 100 °C/s was used in the deformation dilatometry tests where the uniaxial deformation varied from 5-50 %. The theoretical work involved modelling of the martensite formation and the thermal/transformation strains they cause in the steel. Characterizations were done using light optical microscopy, hardness tests and electron backscatter diffraction technique. The parent austenite grains of the martensitic structure were reconstructed using the orientation relationship between the parent austenite and the martensite. Kurdjumov-Sachs orientation relationships have previously been proven to work well for low-carbon steels and was therefore selected.

The standard implementation of the Koistinen-Marburger equation for martensite formation and a more convenient approach were compared. The latter approach does not require the storage of initial austenite fraction at start of martensite formation. The comparison shows that the latter model works equally well for the martensite formation. The results showed that the use of martensite start and finish temperatures calibrated versus experiments for Hardox 450 works better when computing thermal expansion than use of general relations based on the chemistry of the steel.

The results from deformation dilatometry showed that deformation by compressive uniaxial stresses impedes the martensite transformation. The simplified incremental model works well for deformation with 5 % and 10 %. However, the waviness in the experimental curve for deformation 50 % does not fit the model due vi to large barrelling effect and the large relative expansion for the material that the sample holders are made of.

Crystallographic reconstruction of parent austenite grains were performed on a hot-rolled as-received reference sample and dilatometry samples cooled with 60 °C/s and 100 °C/s. The misorientation results showed that the samples match with the Kurdjumov-Sachs orientation relationship in both hot rolled product and dilatometry samples. When misorientation between adjacent pixels are between 15° and 48°, then the boundary between them was considered as a parent austenite grain. The austenitic grain boundaries of the sample cooled at 100 °C/s is in general identical with the hot rolled sample when considering high angle boundaries (15°-48°). The results from the hardness tests showed that the rolled product exhibits higher hardness as compared to samples cooled by 100 °C/s and 60 °C/s. This can be attributed to the formation of transition-iron-carbides in the hot rolled product due to longer exposure of coiling temperature.

Place, publisher, year, edition, pages
Luleå: Luleå University of Technology, 2017. p. 110
Keywords
Dilatometry, Hardness, EBSD, Martensite, Austenite, Kurdjumov-Sachs, Phase transformation, Modelling
National Category
Other Materials Engineering
Research subject
Steel Forming and Surface Engineering
Identifiers
urn:nbn:se:du-24714 (URN)978-91-7583-839-7 (ISBN)978-91-7583-840-3 (ISBN)
Presentation
2017-04-28, TDB, Luleå, 10:00 (Swedish)
Opponent
Supervisors
Available from: 2017-04-18 Created: 2017-04-18 Last updated: 2019-03-06Bibliographically approved
Gyhlesten Back, J. (2016). Simplified Implementation of the Koistinen-Marburger Model for Use in Finite Element Simulations. In: Proceedings of the 11th international congress on thermal stresses: . Paper presented at Proceedings of the 11th international congress on thermal stresses, Salerno, Italy, June 5–9, 2016 (pp. 107-110). Severino: Edizioni Paguro
Open this publication in new window or tab >>Simplified Implementation of the Koistinen-Marburger Model for Use in Finite Element Simulations
2016 (English)In: Proceedings of the 11th international congress on thermal stresses, Severino: Edizioni Paguro , 2016, p. 107-110Conference paper, Published paper (Other academic)
Place, publisher, year, edition, pages
Severino: Edizioni Paguro, 2016
Keywords
Martensite, Modelling, Phase Transformation
National Category
Other Materials Engineering
Research subject
Steel Forming and Surface Engineering
Identifiers
urn:nbn:se:du-24713 (URN)978-88-99509-14-9 (ISBN)
Conference
Proceedings of the 11th international congress on thermal stresses, Salerno, Italy, June 5–9, 2016
Available from: 2017-03-09 Created: 2017-04-18 Last updated: 2017-04-18Bibliographically approved
Organisations

Search in DiVA

Show all publications