du.sePublikasjoner
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Influence of tool surface topography on the material transfer tendency and tool wear in the turning of 316L stainless steel
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. Ångström Tribomaterials Group, Uppsala University.ORCID-id: 0000-0001-5536-3077
AB Sandvik Coromant, Sandviken.
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. Ångström Tribomaterials Group, Uppsala University. (Tribologi)
2016 (engelsk)Inngår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 368–369, s. 239-252Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Abstract The influence of tool surface topography on the initiation and build-up of transfer layers in the orthogonal turning of 316L austenitic stainless steel have been studied under well controlled conditions. Tool materials include CVD Ti(C,N)-Al2O3-TiN and PVD (Ti, Al)N-(Al,Cr)2O3 coated cemented carbide inserts prepared using different grinding and polishing treatments. Post-test characterization of the inserts was performed using high resolution scanning electron microscopy and energy dispersive X-ray spectroscopy. The results show that the transfer tendency of work material is strongly affected by the surface topography of the rake face. For both types of inserts, the initial transfer and the build-up of transfer layers are localised to microscopic surface irregularities on the rake face. Consequently, an appropriate surface treatment of the cemented carbide substrate before coating deposition and the as-deposited CVD and PVD coating can be used in order to reduce the transfer tendency and the mechanical interaction between the mating surfaces. Also, an improved surface finish was found to reduce coating wear and consequently the crater wear rate of the inserts investigated. This can most likely be explained by the reduced tendency to discrete chipping of coating fragments in the contact zone and the formation of a thin transfer layer composed of Al, Si, Ca, O with beneficial friction properties which are promoted by a smooth coating surface.

sted, utgiver, år, opplag, sider
Elsevier, 2016. Vol. 368–369, s. 239-252
Emneord [en]
Turning, Material transfer, Surface topography, Coatings, Stainless steel
HSV kategori
Forskningsprogram
Stålformning och ytteknik
Identifikatorer
URN: urn:nbn:se:du-23253DOI: 10.1016/j.wear.2016.09.023ISI: 000390733400026OAI: oai:DiVA.org:du-23253DiVA, id: diva2:1033855
Tilgjengelig fra: 2016-10-10 Laget: 2016-10-10 Sist oppdatert: 2019-03-19bibliografisk kontrollert
Inngår i avhandling
1.
Posten ble ikke funnet. Det kan skyldes at posten ikke lenger er tilgjengelig eller det er feil id i adressefeltet.

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekst

Søk i DiVA

Av forfatter/redaktør
Saketi, SaraOlsson, Mikael
Av organisasjonen
I samme tidsskrift
Wear

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 695 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf