du.sePublikasjoner
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Wear mechanism of cemented carbide cutting tool in the turning of 316L stainless steel
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. Uppsala University. (Tribology)ORCID-id: 0000-0001-5536-3077
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. (Tribology)
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. Uppsala University. (Tribology)
2018 (engelsk)Konferansepaper, Publicerat paper (Fagfellevurdert)
sted, utgiver, år, opplag, sider
2018.
Emneord [en]
Cemented carbide; stainless steel 316 L; turning; SEM; AES
HSV kategori
Forskningsprogram
Stålformning och ytteknik
Identifikatorer
URN: urn:nbn:se:du-28052OAI: oai:DiVA.org:du-28052DiVA, id: diva2:1229064
Konferanse
The 18th Nordic Symposium on Tribology – NORDTRIB 2018 18-21 June 2018, Uppsala University, Uppsala, Sweden
Tilgjengelig fra: 2018-06-29 Laget: 2018-06-29 Sist oppdatert: 2019-03-27bibliografisk kontrollert
Inngår i avhandling
1.
Posten ble ikke funnet. Det kan skyldes at posten ikke lenger er tilgjengelig eller det er feil id i adressefeltet.
2. Investigation of topography, adhesion and diffusion in sliding contacts during steel and titanium alloy machining
Åpne denne publikasjonen i ny fane eller vindu >>Investigation of topography, adhesion and diffusion in sliding contacts during steel and titanium alloy machining
2019 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

The aim of the present thesis work is to increase the fundamental knowledge of the tribological contact between the cutting tool and the work material in three different cutting operations, i.e. hard milling of cold work tool steels, turning in 316L stainless steel and turning in Ti6Al4V alloy, respectively. The influence of cutting parameters and tool surface topography on the initial material transfer tendency and resulting wear and wear mechanisms were investigated under well controlled cutting conditions. High resolution scanning electron microscopy (SEM) and surface analysis, including energy dispersive X-ray spectroscopy (EDS), Auger electron spectroscopy (AES) and time-of-flight secondary ion mass spectrometry (ToF-SIMS), were used in order to characterize the worn cutting tools on a sub-µm scale and deepen the understanding of the wear mechanisms prevailing at the tool / work material interface. The characterization work includes the analysis of worn tool surfaces as well as cross-sections of these. Also, the back side of collected chips were analysed to further understand the contact mechanisms between the tool rake face and chip.

The results show that the transfer tendency of work material is strongly affected by the surface topography of the rake face and that an appropriate pre- and post-coating treatment can be used in order to reduce the transfer tendency and the mechanical interaction between the mating surfaces. The continuous wear mechanisms of the cutting tools were found to be dependent on the work materials and the cutting parameters used. In hard milling of cold work tool steels, polycrystalline cubic boron nitride shows a combination of tribochemical wear, adhesive wear and mild abrasive wear. In the turning of 316L stainless steel and Ti6Al4V alloy, using medium to high cutting speeds/feeds, the wear of cemented carbide is mainly controlled by diffusion wear of the WC phase. Interestingly, the diffusion wear processes differ between the two work materials. In contact with 316L stainless steel crater wear is controlled by atomic diffusion of W and C into the passing chip. In contact with Ti6Al4V crater wear is controlled by the diffusion of C into a transfer work material layer generating a W-rich and TiC interfacial layer which repeatedly is removed by the passing chip. The experimental work and results obtained illustrates the importance of in-depth characterization of the worn surfaces in order to increase the understanding of the degradation and wear of tool materials and coatings in metal cutting operations.

sted, utgiver, år, opplag, sider
Uppsala University, 2019
HSV kategori
Forskningsprogram
Stålformning och ytteknik
Identifikatorer
urn:nbn:se:du-29700 (URN)
Disputas
(engelsk)
Veileder
Tilgjengelig fra: 2019-03-27 Laget: 2019-03-19 Sist oppdatert: 2019-04-08bibliografisk kontrollert

Open Access i DiVA

fulltext(469 kB)56 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 469 kBChecksum SHA-512
eeef5b794bd320da5c5601b8143d8de8365b4161250bd050e794174f932c948b1b88623f9fe4181f2a7bb715b3276355329ff4b4e22427b539e19e3b0b14350a
Type fulltextMimetype application/pdf

Personposter BETA

Saketi, SaraBexell, UlfOlsson, Mikael

Søk i DiVA

Av forfatter/redaktør
Saketi, SaraBexell, UlfOlsson, Mikael
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 56 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

urn-nbn

Altmetric

urn-nbn
Totalt: 128 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf