du.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Influence of tool surface topography on the material transfer tendency and tool wear in the turning of 316L stainless steel
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. Ångström Tribomaterials Group, Uppsala University.ORCID-id: 0000-0001-5536-3077
AB Sandvik Coromant, Sandviken.
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. Ångström Tribomaterials Group, Uppsala University. (Tribologi)
2016 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 368–369, s. 239-252Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Abstract The influence of tool surface topography on the initiation and build-up of transfer layers in the orthogonal turning of 316L austenitic stainless steel have been studied under well controlled conditions. Tool materials include CVD Ti(C,N)-Al2O3-TiN and PVD (Ti, Al)N-(Al,Cr)2O3 coated cemented carbide inserts prepared using different grinding and polishing treatments. Post-test characterization of the inserts was performed using high resolution scanning electron microscopy and energy dispersive X-ray spectroscopy. The results show that the transfer tendency of work material is strongly affected by the surface topography of the rake face. For both types of inserts, the initial transfer and the build-up of transfer layers are localised to microscopic surface irregularities on the rake face. Consequently, an appropriate surface treatment of the cemented carbide substrate before coating deposition and the as-deposited CVD and PVD coating can be used in order to reduce the transfer tendency and the mechanical interaction between the mating surfaces. Also, an improved surface finish was found to reduce coating wear and consequently the crater wear rate of the inserts investigated. This can most likely be explained by the reduced tendency to discrete chipping of coating fragments in the contact zone and the formation of a thin transfer layer composed of Al, Si, Ca, O with beneficial friction properties which are promoted by a smooth coating surface.

Ort, förlag, år, upplaga, sidor
Elsevier, 2016. Vol. 368–369, s. 239-252
Nyckelord [en]
Turning, Material transfer, Surface topography, Coatings, Stainless steel
Nationell ämneskategori
Materialteknik
Forskningsämne
Stålformning och ytteknik
Identifikatorer
URN: urn:nbn:se:du-23253DOI: 10.1016/j.wear.2016.09.023ISI: 000390733400026OAI: oai:DiVA.org:du-23253DiVA, id: diva2:1033855
Tillgänglig från: 2016-10-10 Skapad: 2016-10-10 Senast uppdaterad: 2019-03-26Bibliografiskt granskad
Ingår i avhandling
1. Investigation of topography, adhesion and diffusion in sliding contacts during steel and titanium alloy machining
Öppna denna publikation i ny flik eller fönster >>Investigation of topography, adhesion and diffusion in sliding contacts during steel and titanium alloy machining
2019 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The aim of the present thesis work is to increase the fundamental knowledge of the tribological contact between the cutting tool and the work material in three different cutting operations, i.e. hard milling of cold work tool steels, turning in 316L stainless steel and turning in Ti6Al4V alloy, respectively. The influence of cutting parameters and tool surface topography on the initial material transfer tendency and resulting wear and wear mechanisms were investigated under well controlled cutting conditions. High resolution scanning electron microscopy (SEM) and surface analysis, including energy dispersive X-ray spectroscopy (EDS), Auger electron spectroscopy (AES) and time-of-flight secondary ion mass spectrometry (ToF-SIMS), were used in order to characterize the worn cutting tools on a sub-µm scale and deepen the understanding of the wear mechanisms prevailing at the tool / work material interface. The characterization work includes the analysis of worn tool surfaces as well as cross-sections of these. Also, the back side of collected chips were analysed to further understand the contact mechanisms between the tool rake face and chip.

The results show that the transfer tendency of work material is strongly affected by the surface topography of the rake face and that an appropriate pre- and post-coating treatment can be used in order to reduce the transfer tendency and the mechanical interaction between the mating surfaces. The continuous wear mechanisms of the cutting tools were found to be dependent on the work materials and the cutting parameters used. In hard milling of cold work tool steels, polycrystalline cubic boron nitride shows a combination of tribochemical wear, adhesive wear and mild abrasive wear. In the turning of 316L stainless steel and Ti6Al4V alloy, using medium to high cutting speeds/feeds, the wear of cemented carbide is mainly controlled by diffusion wear of the WC phase. Interestingly, the diffusion wear processes differ between the two work materials. In contact with 316L stainless steel crater wear is controlled by atomic diffusion of W and C into the passing chip. In contact with Ti6Al4V crater wear is controlled by the diffusion of C into a transfer work material layer generating a W-rich and TiC interfacial layer which repeatedly is removed by the passing chip. The experimental work and results obtained illustrates the importance of in-depth characterization of the worn surfaces in order to increase the understanding of the degradation and wear of tool materials and coatings in metal cutting operations.

Ort, förlag, år, upplaga, sidor
Uppsala University, 2019
Nationell ämneskategori
Materialteknik
Forskningsämne
Stålformning och ytteknik
Identifikatorer
urn:nbn:se:du-29700 (URN)
Disputation
(Engelska)
Handledare
Tillgänglig från: 2019-03-27 Skapad: 2019-03-19 Senast uppdaterad: 2019-04-08Bibliografiskt granskad
2.
Posten kunde inte hittas. Det kan bero på att posten inte längre är tillgänglig eller att du har råkat ange ett felaktigt id i adressfältet.

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Sök vidare i DiVA

Av författaren/redaktören
Saketi, SaraOlsson, Mikael
Av organisationen
Materialteknik
I samma tidskrift
Wear
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 708 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf