du.sePublikasjoner
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Deformation structures in a duplex stainless steel
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik. KTH, Materialvetenskap.ORCID-id: 0000-0002-4359-4967
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik.
2018 (engelsk)Inngår i: Materials Science Forum, ISSN 0255-5476, E-ISSN 1662-9752, Vol. 941, s. 176-181Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The evolution of the deformation structure with strain has been studied using electron backscatter diffraction (EBSD). Samples from interrupted uniaxial tensile tests and from a cyclic tension/compression test were investigated. The evolution of low angle boundaries (LABs) was studied using boundary maps and by measuring the LAB density. From calculations of local misorientations, smaller orientation changes in the substructure can be illustrated. The different orientations developed with strain within a grain, due to operation of different slip systems in different parts of the grain, were studied using a misorientation profile showing substantial orientation changes after a true strain of 0.24. The texture evolution with increasing strain was followed by using inverse pole figures (IPFs). The observed substructure development in the ferritic and austenitic phases could be successfully correlated with the stress-strain curve from a tensile test. LABs were first observed in the different phases when the strain hardening rate changed in appearance indicating that cross slip started to operate as a significant dislocation recovery mechanism. The evolution of the deformation structure is concluded to occur in a similar manner in the austenitic and ferritic phases but with different texture evolution for the two phases.

sted, utgiver, år, opplag, sider
2018. Vol. 941, s. 176-181
Emneord [en]
Duplex stainless steel, Electron backscatter diffraction (EBSD), Structure-property relationship, Tensile test
HSV kategori
Forskningsprogram
Stålformning och ytteknik
Identifikatorer
URN: urn:nbn:se:du-28343DOI: 10.4028/www.scientific.net/MSF.941.176ISI: 000468152500030Scopus ID: 2-s2.0-85064068590OAI: oai:DiVA.org:du-28343DiVA, id: diva2:1239600
Konferanse
THERMEC 2018
Tilgjengelig fra: 2018-05-09 Laget: 2018-08-17 Sist oppdatert: 2019-06-10bibliografisk kontrollert
Inngår i avhandling
1. Experimental Studies of Deformation Structures in Stainless Steels using EBSD
Åpne denne publikasjonen i ny fane eller vindu >>Experimental Studies of Deformation Structures in Stainless Steels using EBSD
2018 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

In this thesis, the focus has been the study of deformation structures in stainless steels by using electron backscatter diffraction (EBSD). Via increased knowledge of the evolution of the substructure during deformation, the design and control of the manufacturing process can be improved.

A relation was found between the active deformation mechanisms, the evolution of low angle boundaries (LABs) and the strain hardening rate. When deformation twinning was an active deformation mechanism in an austenitic stainless steel with lower stacking fault energy (SFE), the strain hardening rate was maintained up to large strains due to formation of LABs. The deformation twin boundaries acted as new obstacles for dislocation slip which in turn increased the formation of LABs even further. During deformation by slip in an austenitic stainless steel with a higher SFE, the strain hardening rate instead decreased when LABs were formed. A high value of SFE promotes dislocation cross slip which in turn increases annihilation of dislocations leading to a minor increase in LAB formation.

Deformation structures formed in surface grains during in situ tensile tests were found to develop at lower strains than in bulk grains obtained from interrupted conventional tensile tests. This behavior is consistent with the fact that dislocations sources and deformation twinning operate at approximately half the stress on a free surface as compared to the bulk.

The deformation structures were quantified by measuring size distributions for entities bounded by LABs and high angle boundaries (HABs). The size distributions were found to be well described by bimodal lognormal distribution functions. The average size for the distribution of small grains and subgrains correlated well with the mean free distance of dislocation slip and to the strain hardening.

sted, utgiver, år, opplag, sider
KTH Royal Institute of Technology, 2018. s. 63
Emneord
EBSD, Austenitic stainless steels, Duplex stainless steel, In situ tensile test, Grain boundaries, Grain rotation, Grain size distribution, Texture, Strain hardening, Structure-property relationship, High strain rate, Wire rod rolling, Roll forming
HSV kategori
Forskningsprogram
Stålformning och ytteknik
Identifikatorer
urn:nbn:se:du-28340 (URN)978-91-7729-772-7 (ISBN)
Disputas
2018-06-05, B2, Brinellvägen 23, Stockholm, 10:00 (svensk)
Opponent
Veileder
Tilgjengelig fra: 2018-08-17 Laget: 2018-08-17 Sist oppdatert: 2018-08-17bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Yvell, KarinEngberg, Göran

Søk i DiVA

Av forfatter/redaktør
Yvell, KarinEngberg, Göran
Av organisasjonen
I samme tidsskrift
Materials Science Forum

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 75 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf