du.sePublikasjoner
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
New understanding of the initiation of material transfer and transfer layer build-up in metal forming: in situ studies in the SEM
Högskolan Dalarna, Akademin Industri och samhälle, Materialvetenskap.
2012 (engelsk)Inngår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 292, s. 61-73Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The tribological mechanisms behind the initiation of material transfer and build-up of transfer layers in aluminium forming have been studied in situ in the SEM where a tip of aluminium is put into contact with a tool steel surface under controlled sliding contact conditions. By combining in situ observations with post-test high resolution FEG-SEM studies of the contacting surfaces we have shown that aluminium is immediately transferred onto the fine polished tool steel. It was also confirmed that the initial transfer occurs on a very fine scale and is localised to the surface irregularities presented by the slightly protruding carbonitrides. In contrast, the less protruding M6C carbides, as well as the martensitic steel matrix exhibit very little initial transfer. Intentionally made scratches (roughly 5 mu m wide and 2 mu m deep) across the tool surface immediately result in larger scale transfer, which grows upon further passages of work material causing a high coefficient of friction. The study illuminates the extreme value of combining the in situ technique with high-resolution scanning electron microscopy using low acceleration voltage as a mean to detect the very thin initial transfer layers. With the higher acceleration voltages normally used, the transferred aluminium becomes transparent and can hardly be detected. (C) 2012 Elsevier B.V. All rights reserved.

sted, utgiver, år, opplag, sider
2012. Vol. 292, s. 61-73
Emneord [en]
Galling; Surface topography; Steel; Electron microscopy
HSV kategori
Forskningsprogram
Stålformning och ytteknik
Identifikatorer
URN: urn:nbn:se:du-11341DOI: 10.1016/j.wear.2012.05.032ISI: 000308628400008OAI: oai:DiVA.org:du-11341DiVA, id: diva2:573050
Tilgjengelig fra: 2012-11-29 Laget: 2012-11-28 Sist oppdatert: 2017-12-07bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekst

Søk i DiVA

Av forfatter/redaktør
Olsson, Mikael
Av organisasjonen
I samme tidsskrift
Wear

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 719 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf