du.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Surface failure and wear of cemented carbide rock drill buttons: the importance of sample preparation and optimized microscopy settings
Atlas Copco.
Atlas Copco.
Atlas Copco.
Högskolan Dalarna, Akademin Industri och samhälle, Materialteknik.
Visa övriga samt affilieringar
2013 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 302, nr 1-2, s. 1546-1554Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The combination of suitable mechanical properties and wear resistance makes cemented carbide one of the most interesting engineering composite materials for tribological applications, such as in rock drilling. Despite the fact that cemented carbide buttons have been used in rock drilling applications for a long time the detailed understanding of the prevailing wear mechanisms is far from complete and wear and breakage of rock drill buttons are still one of the lifetime-limiting factors for rock drill bits. Consequently, further research in this area, including detailed characterization of worn drill button surfaces and sub-surface regions, is needed in order to support the future development of new cemented carbide grades with improved failure and wear resistance. In the present paper, high resolution scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and Auger electron spectroscopy (AES) have been used to characterize the wear and failure mechanisms of worn drill buttons and samples exposed to well controlled impact and scratch tests performed in the laboratory. The most important mechanisms of surface failure and wear were found to be severe plastic deformation, cracking, crushing of individual WC grains and mechanical/tribochemical degradation of the Co binder phase including Co depletion. Fracture cross-sectioning under tensile stress-state was found to be the best method for achieving large and reliable sub-surface cross-sections within a short time and to a low cost. The importance of optimized microscopy and spectroscopy settings for enhanced surface sensitivity for the examination of small-scale tribological phenomena is illuminated and discussed.

Ort, förlag, år, upplaga, sidor
Elsevier, 2013. Vol. 302, nr 1-2, s. 1546-1554
Nyckelord [en]
Rock drilling; WC–Co; Surface degradation; Wear mechanisms; SEM
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Stålformning och ytteknik
Identifikatorer
URN: urn:nbn:se:du-11448DOI: 10.1016/j.wear.2013.01.078ISI: 000322682800082OAI: oai:DiVA.org:du-11448DiVA, id: diva2:576527
Tillgänglig från: 2012-12-13 Skapad: 2012-12-13 Senast uppdaterad: 2017-12-06Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Sök vidare i DiVA

Av författaren/redaktören
Bexell, UlfOlsson, Mikael
Av organisationen
Materialteknik
I samma tidskrift
Wear
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 823 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf