du.sePublications
Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Wear mechanism of cemented carbide cutting tool in the turning of 316L stainless steel
Dalarna University, School of Technology and Business Studies, Materials Technology. Uppsala University. (Tribology)ORCID iD: 0000-0001-5536-3077
Dalarna University, School of Technology and Business Studies, Materials Technology. (Tribology)
Dalarna University, School of Technology and Business Studies, Materials Technology. Uppsala University. (Tribology)
2018 (English)Conference paper, Published paper (Refereed)
Place, publisher, year, edition, pages
2018.
Keywords [en]
Cemented carbide; stainless steel 316 L; turning; SEM; AES
National Category
Engineering and Technology
Research subject
Steel Forming and Surface Engineering
Identifiers
URN: urn:nbn:se:du-28052OAI: oai:DiVA.org:du-28052DiVA, id: diva2:1229064
Conference
The 18th Nordic Symposium on Tribology – NORDTRIB 2018 18-21 June 2018, Uppsala University, Uppsala, Sweden
Available from: 2018-06-29 Created: 2018-06-29 Last updated: 2019-03-27Bibliographically approved
In thesis
1.
The record could not be found. The reason may be that the record is no longer available or you may have typed in a wrong id in the address field.
2. Investigation of topography, adhesion and diffusion in sliding contacts during steel and titanium alloy machining
Open this publication in new window or tab >>Investigation of topography, adhesion and diffusion in sliding contacts during steel and titanium alloy machining
2019 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

The aim of the present thesis work is to increase the fundamental knowledge of the tribological contact between the cutting tool and the work material in three different cutting operations, i.e. hard milling of cold work tool steels, turning in 316L stainless steel and turning in Ti6Al4V alloy, respectively. The influence of cutting parameters and tool surface topography on the initial material transfer tendency and resulting wear and wear mechanisms were investigated under well controlled cutting conditions. High resolution scanning electron microscopy (SEM) and surface analysis, including energy dispersive X-ray spectroscopy (EDS), Auger electron spectroscopy (AES) and time-of-flight secondary ion mass spectrometry (ToF-SIMS), were used in order to characterize the worn cutting tools on a sub-µm scale and deepen the understanding of the wear mechanisms prevailing at the tool / work material interface. The characterization work includes the analysis of worn tool surfaces as well as cross-sections of these. Also, the back side of collected chips were analysed to further understand the contact mechanisms between the tool rake face and chip.

The results show that the transfer tendency of work material is strongly affected by the surface topography of the rake face and that an appropriate pre- and post-coating treatment can be used in order to reduce the transfer tendency and the mechanical interaction between the mating surfaces. The continuous wear mechanisms of the cutting tools were found to be dependent on the work materials and the cutting parameters used. In hard milling of cold work tool steels, polycrystalline cubic boron nitride shows a combination of tribochemical wear, adhesive wear and mild abrasive wear. In the turning of 316L stainless steel and Ti6Al4V alloy, using medium to high cutting speeds/feeds, the wear of cemented carbide is mainly controlled by diffusion wear of the WC phase. Interestingly, the diffusion wear processes differ between the two work materials. In contact with 316L stainless steel crater wear is controlled by atomic diffusion of W and C into the passing chip. In contact with Ti6Al4V crater wear is controlled by the diffusion of C into a transfer work material layer generating a W-rich and TiC interfacial layer which repeatedly is removed by the passing chip. The experimental work and results obtained illustrates the importance of in-depth characterization of the worn surfaces in order to increase the understanding of the degradation and wear of tool materials and coatings in metal cutting operations.

Place, publisher, year, edition, pages
Uppsala University, 2019
National Category
Materials Engineering
Research subject
Steel Forming and Surface Engineering
Identifiers
urn:nbn:se:du-29700 (URN)
Public defence
(English)
Supervisors
Available from: 2019-03-27 Created: 2019-03-19 Last updated: 2019-04-08Bibliographically approved

Open Access in DiVA

fulltext(469 kB)56 downloads
File information
File name FULLTEXT01.pdfFile size 469 kBChecksum SHA-512
eeef5b794bd320da5c5601b8143d8de8365b4161250bd050e794174f932c948b1b88623f9fe4181f2a7bb715b3276355329ff4b4e22427b539e19e3b0b14350a
Type fulltextMimetype application/pdf

Authority records BETA

Saketi, SaraBexell, UlfOlsson, Mikael

Search in DiVA

By author/editor
Saketi, SaraBexell, UlfOlsson, Mikael
By organisation
Materials Technology
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar
Total: 56 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

urn-nbn

Altmetric score

urn-nbn
Total: 128 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • chicago-author-date
  • chicago-note-bibliography
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf